ITEL A23 FRP Lock Remove Using Infinity CM2 Dongle
Itel A23 Google Account Lock Remove Done by Cm2 Dongle. Itel A23 Have Spd Cpu With Locked Bootloader So That it Can’t Unlock by Erase Persist Command.follow These Steps to Unlock Frp 100% ….
Let’s see “how to unlock ITEL A23 frp after factory reset?” If your device is stuck on Google account verification after a factory reset then this tutorial is very useful for you. Here in this guide, we will describe the complete step by step process to remove ITEL A23 FRP without any risk. No, any password required to unlock ITEL A23 android mobile.
As we all know, users can unlock ITEL A23 pattern lock or PIN password by factory reset but if you were using any Google account on the device then it will be stuck on Google account verification after factory reset.
Just enter the existing Google account credentials to unlock ITEL A23 phone. But in case, you don’t know what was the correct ID or password Google account then you have to bypass FRP lock onITEL A23 by following any below methods.
ITEL A23 FRP Unlock Using Infinity CM2 Dongle
1.First Download ITEL A23 Tested Flash File From Here
2.Add Downloaded Pac, Flash File In CM2 Dongle.
3. Go To service Tab Under Service Tab Click On Format FS/ Reset Phone/ Clear FRP
Card found: S/N : D8&&&& , v0135
Chinese Miracle II [SPD module] v 1.22Loading : A23-SU335-8.1-IN-V010-20181017.pac
CRVersion : BP_R1.0.0
PacCPUinfo : sp9832e_1h10
PacVersion : A23-SU335-8.1-IN-V010-20181017
FastCheck : 0x0060AA2CD7Loading files …
File : fdl1-sign.bin
File : fdl2-sign.bin
File : sharkle_pubcp_customer_Smart_Phone_nvitem.bin
File : prodnv.img
File : u-boot-spl-16k-sign.bin
File : SC9600_sharkle_pubcp_customer_Smart_Phone_modem.dat
File : SharkLE_LTEA_DSP_evs_on.bin
File : SHARKLE2_DM_DSP.bin
File : sharkle_cm4.bin
File : PM_sharkle_cm4.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : logo.bmp
File : logo.bmp
File : cache.img
File : u-boot-sign.bin
File : persist.img
File : sharkle_pubcp_customer_Smart_Phone_deltanv.bin
File : sml-sign.bin
File : vendor.img
File : tos-sign.bin
File : gnssbdmodem.bin
File : gnssmodem.bin
File : vbmeta-sign.img
File : sp9832e_1h10.xml
Load Ok!
Operation : Format File System / Reset Settings [ v1.22 ] Settings : SmartFormat is On
Remove battery. Insert battery back
Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
Insert cable==== Wait for phone…
Phone found! [ 45 ] Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Checking Structure …
Detected eMMC Flash , Structure detect Ok!
eMMC phone detected! Will use ‘Safe Format’ mode!
UserData : PART_MOUNT failed! Part Damaged! Will use Repair Mode!
Mount : /cache
Size : 0x0000000007300000
State : 0x0001
Prepare Ok! Format Ok!
Don’t touch phone, until it fully bootup to “Welcome Screen”!
